Goose Decoy Paint Restoration with UV-Protective Coatings
A spread of goose decoys only fools the birds if it holds its colour in the field, and colour is the first thing the sun takes. Paint on moulded plastic and hollow fibreglass bodies chalks, flattens and drifts toward a washed-out grey within a single Australian summer, so a rig that looked convincing in the shed can read as a row of pale plastic bottles from three hundred metres. Restoring that finish is a weekend job that most shooters put off for years, which is exactly why so many cheap decoy spreads end up looking wrong.
What makes the problem worse down here is the light. Australia runs a UV index that regularly tips past eleven in summer, and decoys spend their lives on open water under a sky with almost no atmospheric filter. On top of that sits heat cycling, salt spray at coastal spots like Lakes Entrance or the Coorong, and the habit of chucking the whole spread into the back of a ute or a garage shelf where it bakes for months between seasons.
The good news is that restoration does not have to mean a full respray every year. Most decoys need cleaning, a scuff, a fresh coat of colour-matched paint and a clear topcoat containing proper UV absorbers. Done properly, that topcoat buys you several more seasons of believable colour and takes a lot of the tedium out of spring.
What follows covers how to read the damage, how to clean and prep different body types, which primers and paints suit Australian waterfowl, how to apply a UV-resistant clear coat without it looking like plastic, and how to rig, store and maintain the finished spread.
Why Australian Sun Is Harder on Decoy Paint
Ultraviolet radiation breaks down the binder in paint, and the failure shows as chalking, loss of gloss and a slow bleaching of pigment. Rotation-moulded plastic decoys and blow-moulded shells are particularly vulnerable, because the colour is dispersed through a polymer that yellows and embrittles as it ages. Add the reflected light off water and sand and you get double the exposure of anything stored in shade.
Timing adds a wrinkle. Victorian and New South Wales waterfowl seasons open in mid-winter, which means your decoys spend the entire Australian summer sitting unused in the hottest, brightest part of the year, usually in a trailer or under a tarpaulin in the ute tray. Shooters further north, including Queensland shooters working the coastal wetlands and the Mitchell and Fitzroy districts, face the same problem with even more humidity and salt. Decoys used at the Werribee, on the Murray near Echuca or around the Macquarie marshes will get a shorter lifespan than those kept in a locked shed.
A second factor is that Australian grey and black duck hunters are spread thin, with plenty of time between trips to let a finish deteriorate, so it pays to treat the paint job as maintenance rather than a once-off purchase. Decoy bodies from Avian X, Avery/GHG, Dakota, Mojo Outdoors and Real Geese all respond well to the same restoration routine, and the specialist socks and shell options from Sillosocks make it easy to mix a spread that looks like the birds actually shooting in your district.
Reading the Damage Before You Touch Anything
Start by sorting your spread into three piles: sound, tired and wrecked. Sound decoys need nothing more than a wipe and a storage bag. Tired decoys have lost gloss and colour depth but the surface is still intact. Wrecked ones have peeling paint, cracks, failed seams or soft, stained foam cores, and those are the ones worth the weekend.
Look closely at the paint itself. Chalking shows as a dusty film you can rub off with a thumb. Fading shows as a colour shift, often with the black going brown and the white going cream. Cracking and crazing, usually around the waterline seam and the neck, point to a topcoat that has failed rather than a body that has failed. Fouling from birds and duckweed is a separate issue and needs chemical help, because scrubbing alone just spreads the mess into the paint.
Then work out what you are dealing with structurally. Moulded plastic, hollow fibreglass, foam-bodied knockdowns and timber floats each take different preparation, and mixing up the procedures ruins shells. Foam bodies are the most forgiving; hollow fibreglass is the most brittle; timber is the most work but the most satisfying to restore because the paint soaks into the grain and holds colour beautifully.
A quick note on sourcing replacements before you start: if a timber body is split, rotted or missing its keel weight, replacing it often beats stripping the old paint. Specialist woodworkers such as Sloan Wood Shop build custom decoy bodies and float shells, so you can order a fresh blank and paint it to match your existing spread rather than fighting a compromised original.
Cleaning, Degreasing and Light Sanding
Give every decoy a bath before you sand anything. A bucket of warm water with a small amount of dish detergent and a stiff nylon brush will lift loose dust, salt and grime without touching the finish. For stubborn bird fouling, an enzyme cleaner left to sit for ten minutes works far better than pressure, and a hose rather than a high-pressure washer is gentler on seams and printed detail.
Sand the surface lightly after washing, and match the grit to the job. For a tired but sound decoy, 320 to 400 grit is enough to scuff the old sheen and give the new primer something to grip. For a glossy shell, work up to 600 or 800 and wet sand between coats to keep the surface flat. Take a folded sheet of 400 grit and work in tight circles, checking often, because the paint on cheap knockdowns is thin and the body underneath is foam that scuffs like chalk. Timber takes a coarser start, around 120 to 180 grit, then 220 for the final pass.
Stripping is where amateurs do the most damage. Chemical strippers and aggressive solvent wipes will craze ABS and styrene shells and leave them permanently frosted, which no amount of repainting hides. Reserve strong strippers for timber only, keep them off the ground, and wear gloves and a respirator. Do the work outdoors on a tarp over the lawn, pick a still morning without a hot northerly blowing dust across the driveway, and let the shells dry fully in the shade before anything else goes on.
Primer, Paint and Matching the Birds
Plastic and fibreglass need an adhesion promoter or a bonding primer designed for those substrates; paint straight onto a bare shell will peel off in sheets within weeks. Foam wants a flexible water-based acrylic primer, because rigid coats crack as the body flexes in the cold. Timber takes a quality exterior water-based primer and, if you want a harder finish, a light coat of acrylic undercoat tinted slightly darker than the final colour.
Now the colour, which is where most Australian hunters get it wrong. The birds you are actually imitating matter more than any factory paint code. Pacific black duck, the grey, the Australasian shoveler, the chestnut teal and the hard black and white blocks of the wood duck all read differently in real light than they do on a screen. White-fronted and bar-headed geese occasionally turn up on inland flood plains, and if you are drawing those you will need a much paler head and a distinctly orange-pink bill.
Brands like Avian X and Real Geese build their moulded bodies around specific birds, so repainting a spread is simpler when you replace rather than recolour. If you are painting your own, work from observation rather than guesswork: photograph a bird in the field at the same distance you will be viewing your decoys, note where the highlights sit, and match the shadow tones as closely as the highlights. Flocking powder over the base coat gives the matte, broken texture that fools the eye at range, and it must be applied before any clear coat.
Spray in conditions you can control. Aim for a dry, still day between fifteen and twenty-five degrees, keep the can moving in overlapping passes, and stay two hundred to three hundred millimetres off the surface. Too close and you get runs; too far and you get dust and orange peel. Two thin coats beat one heavy coat every time, and each coat needs proper flash-off before the next goes on.
Applying a UV-Resistive Clear Coat
This is the step that decides how long the restoration lasts. A good clear coat contains UV absorbers and a hindered amine light stabiliser, and it slows the breakdown of both the new paint and the pigment underneath, while adding a sacrificial layer that takes the scratches and the UV hit instead of the colour.
Gloss clear looks wrong on a decoy, because real feathers are matte and a shiny shell reads as a plastic bottle instantly. Matte or satin clear solves this and diffuses the light so the decoy blends better, though it needs careful application to avoid patching. Automotive two-pack clear in a matte finish works well and cures hard; water-based clear is gentler on the lungs and easier to clean up, and acrylic clear coats are fine for touch-ups but offer less UV protection over a full season. Beware cheap polyurethane clear that yellows in sunlight, and be careful with marine varnish, which is genuinely UV stable but ambers noticeably over time and will ruin a clean white breast.
Mask off the keel, any eyelet and the underside, then apply two to three thin coats with twenty to thirty minutes of flash-off between them and a full cure of at least forty-eight hours before the decoy sees water. Work in shade, wear a respirator and gloves, and never spray near a wetland or with livestock, chooks or pet dogs around. A lot of Australian shooters have decoy bodies that were last sealed indoors in a shed; if you are about to do a whole spread at once, schedule it over a couple of clear days rather than trying to rush it in one arvo.
Rigging, Spacing and Long-Term Storage
Paint is only half of the presentation, and the rig matters as much as the finish. Decoys set too tight in a line read as a fence; spread them in a believable formation with the silhouette decoys on the edges and the waterfowl bodies filling the middle. Goose decoys sit higher and larger in the spread than duck, and they want to be positioned so they draw the eye rather than sit in a flat wall. Cords, crimps, swivels, weights and carry bags are what hold it all together, and the trade guide to suspending decoys at depth explains the weights and cord combinations used to set the height and the drift in the water, which is useful reference even though the water is usually a good deal shallower in an Australian dam than in the Mississippi flyway.
Store the finished spread in purpose-made bags, in a dark garage or under cover in the ute, and never leave it on a concrete slab in full sun. Even out of the weather, heat in a closed trailer will degrade clear coat faster than UV alone, so crack a window or the door when you can. Keep decoys off the dirt floor, because damp and grit work into the keel seam and rust the hardware.
Between trips, wipe the shells down with a damp cloth, treat any scuff or chip straight away with a touch-up of the base colour and a thin layer of the same clear coat, and keep a note of the brand and colour you used on each body. A well-restored decoy should need a full respray only every few seasons rather than every year, which is the real return on the time you spend with a scuff block and a spray gun.
If your spread needs bodies, rigging hardware or replacement shells, the Hunting Equipment USA catalogue covers Avian X, Avery/GHG, Dakota, Mojo Outdoors, Sillosocks and Real Geese decoys along with weights, cords, crimps, swivels and carry bags, with free shipping on orders of $1,300 or more, and the blog carries practical guides on weights, spread layout and field setup. Before you paint anything, check the rules for your patch: Victorian shooters need a Game Management Authority licence and the current season dates, New South Wales shooters a DPI licence with specific gear conditions in some districts, and Queensland shooters work under the relevant shorebird protocol with non-toxic shot requirements. Grab one neglected decoy from the pile, strip it back this weekend and you will have a feel for the process before you commit to the whole spread.